Cookies are used on this site to provide the best user experience. If you continue, we assume that you agree to receive cookies from this site. OK

Data Communication Systems Integrated IT & Digital Marketing Solutions with Innovative Technologies

RS232/FO 850 T

PSI-MOS-RS232/FO 850 T Serial to Fiber Converter
RS232 to Redundant Fiber

  • PSI-MOS-RS232/FO 850 T Serial to Fiber Converter
  • Two ST type fiber connectors
  • Extend serial data up to 2.6 miles
  • Immune to EMI, RFI and transient surges
  • Point-to-point or star configuration
  • Configurable DB9 Male DTE / DCE RS232 Connector

For applications where redundancy is required, the PSI-MOS-RS232/FO 850 T Serial to Fiber Converter transparently connects RS232 devices to two fiber optic cables. By transmitting RS232 data over optical fiber, these serial media converters provide an economical path to extend the reach of serial devices. The serial data input is transmitted out both fiber ports to different locations or back-up systems.

Expandable Serial to Fiber Network infrastructures

Up to ten (10) Serial to Fiber Converters can be grouped together using the TBUS DIN Rail bus system for voltage and data. This allows the serial converter to operate in additional network topology environments:

  • as a star coupler, taking the serial data input signal and distributing it to up to 20 Fiber optic output ports
  • linear structure can be used to network several RS-232 devices to form a master/slave structure

Long Distance Serial Data Transmission over Fiber

RS232 Serial transmission is limited to 20 Kbps for a distance of only 15 meters (50 feet). With the FO 850 T Serial to Fiber Converter serial data transmission can be extended up to 4.2km (2.6 miles). Therefore, any two pieces of asynchronous serial equipment, located miles apart, can communicate at half or full duplex over fiber optic cable at rates up to 115.2 kbps.

EMI, RFI and Transient Surge Immunity

The FO 850 T fiber optic transmission system electrically isolates connected devices. Electromagnetic interference (EMI) is a common phenomenon in industrial environments. This interference can cause corruption of data over serial or copper-based Ethernet links. However, data transmitted over fiber optic cable is completely immune to this type of noise. This prevents the negative effects of voltage equalization currents and electromagnetic interference on the data cables. A Serial to Fiber Media Converter therefore enables you to inter-connect your serial devices over fiber ensuring optimal data transmission, increased availability of the system, and improved network design flexibility for point-to-point connections, linear networks and star topology networks.

Flexible Fiber Optic Connections

The FO 850 T operates at 850 nm wavelength, using a separate LED emitter and photo-detector on both ST type connectors. Almost any multimode glass fiber size can be used including 50/125 m, 62.5/125 m, and 200/230 m.

Power Budget Considerations

Calculating the power budget is critically important when planning the fiber optic link. The optical power budget is the amount of light required to transmit data successfully through a fiber-optic connection. The amount of light energy available within the setup will dictate the length of the fiber optic cable run between serial media converters within the network. Optical power budgets are critical to help businesses avoid signal distortion. To learn how to calculate optical power budget read our technical note. Transmit and receive dBm can be found in the Hardware specifications.

High Quality Features and Support

For efficient troubleshooting and less on-site maintenance, the FO 850 T are equipped with comprehensive diagnostic functions to increase system availability, simplify start-up and permanently monitor the optical transmission quality. These cost and time saving features, along with free worldwide technical support, make the FO 850 T RS232 serial to fiber converter the smart choice for IT professionals.

  • Connections can be plugged in using a COMBICON screw terminal block
  • Supply voltage and data signals routed through via DIN rail connectors
  • High-quality electrical isolation between all interfaces (RS-232, fiber optic ports, power supply, DIN rail connector)
  • Redundant power supply possible by means of optional system power supply unit
  • Approved for use in zone 2
  • Floating switch contact for leading alarm generation in relation to critical fiber optic paths
  • Intrinsically safe fiber optic interface (Ex op is) for direct connection to devices in zone 1
  • Integrated optical diagnostics for continuous monitoring of fiber optic paths
  • Automatic data rate detection for all data rates up to 115.2 kbps

 

PSI-MOS-RS232/FO 850 T Serial to Fiber Media Converter Applications

  • near heavy electrical equipment
  • in environments with electrical (EMI) or radio (RFI) interference
  • in environments with transient surges
  • in industrial plants, warehouses and factory floors
  • enabling asynchronous serial equipment to communicate at half or full duplex, with rates up to 115.2 kbps, over optical fiber

Redundant Point-to-point connections between serial devices over fiber
Configure the point-to-point connection redundantly to increase availability by using two PSI-MOS-RS232/FO 850 T Serial to Fiber Converters. Easily convert a data link from a single copper cable out to two fiber optic cables.

Redundant Point to Point Network Diagram


Linear Networks
The fiber optic linear structure can be used to network several RS-232 devices to form a master/slave structure. In this case, it must be possible to address all the RS-232 devices via communication software. PSI-MOS-RS232/FO 850 E serial to fiber converters are used at the beginning and end of the fiber optic line. PSI-MOS-RS232/FO 850 T serial to fiber converters with two fiber optic ports are used along the line. You can use up to ten PSI-MOS-RS232/FO devices along the line in a linear structure.

Linear Network Diagram

Redundant Star Networks
You can network RS-232 devices within a star structure as a master/slave network. Depending on the number of star lines required, several PSI-MOS-RS232/FO 850 T Serial to Fiber Converters are connected to TBUS DIN Rail bus systems for voltage and data. This makes up to 20 fiber optic ports available. Cross-wiring for RS-232 data and for the supply voltage is provided automatically by the DIN rail connector.

Redundant Star Network Diagram

Block Diagram

PSI-MOS-RS232/FO 850 T E Block Diagram