Data Communication Systems Ολοκληρωμένες Λύσεις Πληροφορικής & Digital Marketing με Καινοτόμες Τεχνολογίες

PSI-MOS-RS485W2/FO 1300 E Serial to Fiber Converter
Connect 2-wire RS485 devices to fiber optic cable

  • PSI-MOS-RS485W2/FO 1300 E Serial to Fiber Converter
  • Extend serial data up to 28 miles
  • Immune to EMI, RFI and transient surges
  • Point-to-point or star configuration
  • SC type fiber connectors
  • Terminal Block for 2-wire RS485 Connections

The PSI-MOS-RS485W2/FO 1300 E can be used to convert RS485 2-wire devices to fiber optics. By transmitting serial data over optical fiber, these serial media converters provide an economical path to extend the reach of RS485 devices. All protocols with 10/11-bit UART data format and NRZ data coding are supported. This includes popular protocols such as:

  • Modbus ASCII / MODBUS RTU
  • SUCONET K
  • S-BUS
  • DH-485, and more…

Long Distance Serial Data Transmission over Fiber

RS485 Serial transmission is commonly limited to 100 kbps over a distance of only 1200 meters (4000 feet). Using the FO 1300 E Serial to Fiber Converter you can extend your serial data transmission up to 27km (16.7 miles) over multimode fiber or 45km (28 miles) over single mode fiber. The result is that any two pieces of asynchronous serial equipment, located miles apart, can communicate at half duplex over fiber optic cable at rates up to 500 kbps.

EMI, RFI and Transient Surge Immunity

Another advantage of the FO 1300 E fiber optic transmission system is the electrically isolated connection of devices. Electromagnetic interference (EMI) is a common phenomenon in typical environments like industrial plants, warehouses and factory floors. This interference can cause corruption of data over RS485 or copper-based Ethernet links. Data transmitted over fiber optic cable however is completely immune to this type of noise, thus preventing the negative effects of voltage equalization currents and electromagnetic interference on the data cables. A Serial to Fiber Media Converter therefore enables you to inter-connect your serial devices over fiber ensuring optimal data transmission, increased availability of the system, and improved network design flexibility for point-to-point connections and star structures.

Flexible Fiber Optic Connections

The FO 1300 E operates at 1300 nm wavelength, using a separate LED emitter and photo-detector on SC type connectors. Almost any multimode or single mode glass fiber size can be used.

Power Budget Considerations

Calculating the power budget is critically important with planning the fiber optic link. The optical power budget is the amount of light required to transmit data successfully over distance through a fiber-optic connection. The amount of light energy available within the setup will dictate the length of the fiber optic cable run between serial media converters within the network. Optical power budgets are critical to help businesses avoid signal distortion.To learn how to calculate optical power budget read our technical note. Transmit and receive dBm can be found in the Hardware specifications.

Transmit each serial signal out over 10 fiber optic lines

Up to ten (10) Serial to Fiber Converters can be grouped together using the TBUS DIN Rail bus system for voltage and data. This allows the serial converter to operate as a star coupler, taking the serial data input signal and distributing it to all Fiber optic output ports.

High Quality Features and Support

The FO 1300 E are also equipped with comprehensive diagnostic functions to increase system availability, simplify start-up and permanently monitor the optical transmission quality. The integrated optical diagnostics allow permanent monitoring of the FO paths during installation and operation. The floating switch contact is activated when the signal level on the fiber optic paths reaches a critical level. This early alarm generation enables critical system states to be detected before they result in failure. These cost and time saving features, along with free worldwide technical support, make the FO 1300 E serial to fiber converter the smart choice for IT professionals.

  • Supply voltage and data signals routed through via DIN rail connectors
  • Connections can be plugged in using a COMBICON screw terminal block
  • Automatic data rate detection or fixed data rate setting via DIP switches
  • Redundant power supply possible by means of optional system power supply unit
  • High-quality electrical isolation between all interfaces (RS-485, fiber optic ports, power supply, DIN rail connector)
  • Approved for use in zone 2
  • Integrated optical diagnostics for continuous monitoring of fiber optic paths
  • Floating switch contact for leading alarm generation in relation to critical fiber optic paths
  • Suitable for data rates up to 500 kbps

PSI-MOS-RS485/FO 1300 E Serial to Fiber Media Converter Applications

  • near heavy electrical equipment
  • in environments with electrical (EMI) or radio (RFI) interference
  • in environments with transient surges
  • in industrial plants, warehouses and factory floors
  • enabling asynchronous serial equipment to communicate at half duplex, with rates up to 500 kbps, over optical fiber

Point-to-point connections between serial devices over fiber
You can use two PSI-MOS-RS485W2/FO 1300 E Serial to Fiber Converters to easily convert a data link from copper cable to fiber optics.

RS485 Point to Point Network Diagram

Linear Networks
The PSI-MOS-RS485W2/FO 1300 E device can be used to network several RS-485 devices to form a linear structure. Devices are used in conjunction with DIN rail connectors along the line.

RS485 Linear Network Diagram

Star structures
You can network RS-485 2-wire devices within a star structure. Depending on the number of star lines required, several PSI-MOS-RS485W2/FO 1300 E Serial to Fiber Converters are connected to TBUS DIN Rail bus systems for voltage and data. This makes up to 10 fiber optic ports available. Cross-wiring for serial data and for the supply voltage is provided automatically by the DIN rail connector.

RS485 Star Network Diagram

Tree structures

Linear and star structures can be cascaded to create complex tree structures. The number of devices that can be cascaded is only limited by the timing response (timeout) of the bus system used due to the bit retiming of the PSI-MOS-RS485W2/FO 1300 E fiber optic converter.

Tree Network Diagram

Block Diagram

PSI-MOS-RS485/FO 1300 E Block Diagram

1.732,00  (2.147,68  συμπ. Φορου)
1 Year, Perle Systems

PSI-MOS-RS485W2/FO1300 E - RS485 2-wire to fiber converter. Terminal block serial to duplex fiber 1300nm ( SC ). Multimode [27km, 16.7 miles], single mode [ 45km, 28 miles ] – 24VDC EU wall power adapter included

 

1.715,00  (2.126,60  συμπ. Φορου)
1 Year, Perle Systems

PSI-MOS-RS422/FO1300 E - RS422/485 4-wire to fiber Converter: Terminal block serial to duplex fiber 1300nm (SC). Multimode [27km, 16.7 miles], single mode [ 45km, 28 miles ]

 

1.715,00  (2.126,60  συμπ. Φορου)
1 Year, Perle Systems

PSI-MOS-RS485W2/FO1300 E - RS485 2-wire to fiber Converter: Terminal block serial to duplex fiber 1300nm (SC). Multimode [27km, 16.7 miles], single mode [ 45km, 28 miles ]